Версия прошивки
--------------------------------------------------------------------------
Linux version 3.10.4 (cyberwrt@cyberwrt) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37816) ) #1 Mon Nov 25 16:28:55 MSK 2013
--------------------------------------------------------------------------
Информация о CPU
system type : Atheros AR9330 rev 1
machine : TP-LINK TL-MR3020
После установки пакетов
kmod-usb-core
kmod-usb-ohci
kmod-usb-uhci
kmod-usb2
+
usbutils Все определилось и заработало
Определяться после установки usbutils и у меня стало:
Цитата:
Сообщение от lsusb
Bus 001 Device 002: ID 1a40:0201 Terminus Technology Inc. FE 2.1 7-port Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 1687:3257 Kingmax Digital Inc.
Bus 001 Device 004: ID 046d:c312 Logitech, Inc. DeLuxe 250 Keyboard
А вот в папке dev нет папки input и, соответственно, файла event0:
Файл /proc/bus/input/devices пустой.
В фале /proc/bus/input/handlers одна строка:
N: Number=0 Name=evdev Minor=64
В чем может быть проблема?
Ведь на Attitude Adjustment 12.09 всё отлично работало на этом же железе.
[ 10.360000] hub 1-1:1.0: USB hub found
[ 10.360000] hub 1-1:1.0: 7 ports detected
[ 10.640000] usb 1-1.2: new low-speed USB device number 3 using ehci-platform
[ 10.760000] input: LITEON Technology USB Multimedia Keyboard as /devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.0/input/input0
[ 10.770000] generic-usb 0003:046D:C312.0001: input: USB HID v1.10 Keyboard [LITEON Technology USB Multimedia Keyboard] on usb-ehci-platform-1.2/input0
[ 13.140000] device eth0 entered promiscuous mode
[ 13.370000] eth0: link up (100Mbps/Full duplex)
[ 13.370000] br-lan: port 1(eth0) entered forwarding state
[ 13.380000] br-lan: port 1(eth0) entered forwarding state
[ 15.380000] br-lan: port 1(eth0) entered forwarding state
Цитата:
Сообщение от dmesg
[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Mon Sep 3 17:51:18 UTC 2012
[ 0.000000] MyLoader: sysp=444ba8b5, boardp=5fbcaeef, parts=ebc66edc
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802ec430, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-MR3020 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29136k/32768k available (2198k kernel code, 3632k reserved, 412k data, 208k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-MR3020
[ 0.340000] bio: create slab <bio-0> at 0
[ 0.350000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.360000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.370000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.380000] TCP reno registered
[ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] NET: Registered protocol family 1
[ 0.400000] PCI: CLS 0 bytes, default 32
[ 0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.430000] msgmni has been set to 56
[ 0.430000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.440000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.460000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.470000] console [ttyATH0] enabled, bootconsole disabled
[ 0.480000] m25p80 spi0.0: found s25sl032a, expected m25p80
[ 0.480000] m25p80 spi0.0: s25sl032a (4096 Kbytes)
[ 0.490000] 5 tp-link partitions found on MTD device spi0.0
[ 0.500000] Creating 5 MTD partitions on "spi0.0":
[ 0.500000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.510000] 0x000000020000-0x000000108424 : "kernel"
[ 0.510000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.520000] 0x000000108424-0x0000003f0000 : "rootfs"
[ 0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.540000] mtd: partition "rootfs" set to be root filesystem
[ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=120000
[ 0.560000] 0x0000002d0000-0x0000003f0000 : "rootfs_data"
[ 0.560000] 0x0000003f0000-0x000000400000 : "art"
[ 0.570000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.590000] ag71xx_mdio: probed
[ 0.600000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.150000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd041, driver=Generic PHY]
[ 1.160000] TCP cubic registered
[ 1.160000] NET: Registered protocol family 17
[ 1.170000] 8021q: 802.1Q VLAN Support v1.8
[ 1.170000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.180000] Freeing unused kernel memory: 208k freed
[ 3.080000] Registered led device: tp-link:green:3g
[ 3.080000] Registered led device: tp-link:green:wlan
[ 3.080000] Registered led device: tp-link:green:lan
[ 3.080000] Registered led device: tp-link:green:wps
[ 5.170000] eth0: link up (100Mbps/Full duplex)
[ 6.380000] JFFS2 notice: (440) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 11 of xref (0 dead, 2 orphan) found.
[ 6.500000] eth0: link down
[ 8.350000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 8.350000] Backport based on wireless-testing.git master-2012-07-16
[ 8.360000] compat.git: wireless-testing.git
[ 8.520000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.530000] cfg80211: World regulatory domain updated:
[ 8.530000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.540000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.550000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.560000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.570000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.570000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.780000] usbcore: registered new interface driver usbfs
[ 8.790000] usbcore: registered new interface driver hub
[ 8.800000] usbcore: registered new device driver usb
[ 9.280000] ath: EEPROM regdomain: 0x0
[ 9.280000] ath: EEPROM indicates default country code should be used
[ 9.280000] ath: doing EEPROM country->regdmn map search
[ 9.280000] ath: country maps to regdmn code: 0x3a
[ 9.280000] ath: Country alpha2 being used: US
[ 9.280000] ath: Regpair used: 0x3a
[ 9.280000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 9.280000] Registered led device: ath9k-phy0
[ 9.280000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 9.290000] cfg80211: Calling CRDA for country: US
[ 9.300000] cfg80211: Regulatory domain changed to country: US
[ 9.300000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.310000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 9.320000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 9.320000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.330000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.340000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.350000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 9.410000] PPP generic driver version 2.4.2
[ 9.560000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.680000] NET: Registered protocol family 24
[ 9.700000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.700000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 9.710000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 9.750000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 9.770000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 9.770000] hub 1-0:1.0: USB hub found
[ 9.770000] hub 1-0:1.0: 1 port detected
[ 9.800000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
[ 10.040000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.170000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 10.310000] usbcore: registered new interface driver usbhid
[ 10.310000] usbhid: USB HID core driver
[ 10.360000] hub 1-1:1.0: USB hub found
[ 10.360000] hub 1-1:1.0: 7 ports detected
[ 10.640000] usb 1-1.2: new low-speed USB device number 3 using ehci-platform
[ 10.760000] input: LITEON Technology USB Multimedia Keyboard as /devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.0/input/input0
[ 10.770000] generic-usb 0003:046D:C312.0001: input: USB HID v1.10 Keyboard [LITEON Technology USB Multimedia Keyboard] on usb-ehci-platform-1.2/input0
[ 13.140000] device eth0 entered promiscuous mode
[ 13.370000] eth0: link up (100Mbps/Full duplex)
[ 13.370000] br-lan: port 1(eth0) entered forwarding state
[ 13.380000] br-lan: port 1(eth0) entered forwarding state
[ 15.380000] br-lan: port 1(eth0) entered forwarding state